A very frequently encountered problem with the Chevy Cruze or any other newer GM vehicle is that of the “Service StabiliTrak” warning.
StabiliTrak is among the most advanced and crucial safety features that you can find on a GM vehicle.
StabiliTrak was designed to avoid accidents by providing greater control over your Cruze.
If you have a service StabiliTrak warning, your Cruze is no longer supported if a decrease in lateral traction occurs.
How To Fix Service Stabilitrak Chevy Cruze?
Here are the four steps to reset and fix the same-
- Firstly, turn the handwheel in a clockwise direction.
- Then, shut off the vehicle and wait for about ten seconds.
- And then turn it back again.
PS – Check for more fixes below.
Fixing the Service StabiliTrak Chevy Cruze in all situations:
Stabilitrak Service message signifies an error in the Stabilitrak system, a TCS, or traction control system (TCS) found in all safety-rated standard vehicles.
The cause of the Service Stabilitrack alert can also be a malfunctioning input sensor.
Or this can be due to a malfunctioning controller or a sensor wired incorrectly.
- Pre-Check #1 – Check that you have the Stabilitrak button that isn’t pressed manually.
- Pre-Check #2 – The Stabilitrak system may not function because of the current conditions of the weather.
- If none of these assertions are true, keep reading for the steps to restart the system.
- Step 1: Turn the handwheel clockwise. (If it stops, the vehicle does not require service, but if it does, proceed to the next step.)
- Step 2: Switch off the car
- And Step 3: Wait 15 seconds.
- Step 4. Turn the car on.
- This Service StabiliTrak error message indicates the existence of an issue. StabiliTrak can be fixed by resetting the engine’s basic ignition.
Fixes for chevy – Switch off your car.
- It should be left to rest for a minimum of 20 minutes.
- If you restart your standby car, this warning will go away.
- If not, then you need help.
PS – If the DIC message does not appear, the vehicle is no longer needed repair.
If the message is still there calling your local dealer or professional repair shop to get assistance.
Cost for fixing the Service Stabilitrak:
Replacing the traction control unit known as StabiliTrak for cars generally costs $80 to $190.
- And this includes the labor cost and can range between $30 to $50, dependent on the model.
- However, the price of this job ranges between $20 and $40 per piece.
- Certain vehicles that have issues having Service Stabilitrak warnings may require the replacement of the sensor, which can cost between $250-$400 per vehicle.
- It is suggested to investigate every possible cause before deciding which option to take.
- If neither of the above solutions works, bring your car to the nearest mechanic shop to have it repaired.
Chevy Cruze – Service StabiliTrak Symptoms and Causes:
The loss of StabiliTrak isn’t likely to be observed during normal driving. It’s only a matter of use in emergencies.
Common Symptoms –
- Service StabiliTrak Warning – The most obvious sign of something’s wrong is the Cruze’s “Service StabiliTrak” warning light.
- Cruise Control – If the StabiliTrak system is operating correctly, the Cruze might be unable to control the cruise feature.
- Traction Control not working – traction control system generally utilizes identical sensors that identify the condition of a wheel’s traction.
- In contrast to StabiliTrak that controls problems with lateral movement (sliding), Traction control stops the wheels from spinning in a way that isn’t needed.
- And this prevents the acceleration of the lateral side completely.
Causes –
- Various things could result in the StabiliTrak system ceasing to perform its job. It’s a complicated system.
- Wheel Speed Sensor – When one or more of the wheel speed sensors are missing, the Cruze won’t be able to tell whether all wheels are spinning at the same rate.
- Without this information, it will activate the StabiliTrak service warning.
- A brake pedal switch can do more than determine whether you have your lights for brakes on or off.
- The ECU uses this switch to control StabiliTrak or cruise control systems. If the switch doesn’t function correctly, these systems could be disabled.
- The wrong size tire– StabiliTrak could not function correctly when the tire dimensions were not in line with GM’s size.
PS – Other problems could result in the StabiliTrak system stopping functioning.
It’s best to check and determine whether you are experiencing any issues with the codes. They could provide solutions to fix it.
Some other questions,
Related Questions and Frequently Asked Questions (FAQ):
Q1.) How much cost does one need to fix a StabiliTrak on Chevy Cruze?
Answer: $80 to $110 is the average costing for replacing a traction control system for your car.
$30 to $50 for labor costs depending on the manufacturer type.
Q2.) How can one service the StabiliTrak?
Answer: Begin by turning the handwheel in the clockwise direction.
Then shut off the vehicle, wait for some time, and turn it on again.
Q3.) What are the causes for StabiliTrak light to come on?
Answer: There can be many reasons for this anomaly, like a faulty speed sensor, a problem in the steering angle sensor, or a faulty speed sensor.
Q4.) Is it okay to drive with the StabiliTrak light as ON?
Answer: Yes, no worries about that. One must keep in mind that you can have some safety hazards in certain situations like sliding ways.
Q5.) What are the implications of a faulty StabiliTrak?
Answer: Some common symptoms are Hard shifting, warning lights, the loss of power, and some trouble codes that appear alongside the issue.
Q6.) Why does the Chevy Cruze show that my engine power has been reduced?
Answer: It occurs whenever there is an underlying issue with your electronic throttle control system.
In addition, they also offer a general warranty extension for the accelerator.
Q7.) Where can one locate the traction control sensor on 2014 Chevy C?
Answer: You can locate the traction control sensor to the left of the dashboard where the headlight switch is there.
Q8.) What are some signs of a bad traction control module?
Answer: Three most common signs here are Checking engine light coming on, car braking issues, and no depression in the control switch.
Q9.) Is there any warranty on StabiliTrak?
Answer: No, most of the powertrain warranty predominantly covers the internal parts of an engine, its transmission, the transfer cases, and axle components.
Q10.) What controls the StabiliTrak?
Answer: It is a stability control system and, as the name suggests, the proper traction and stability on slippery or icy roads.
On the other hand, a standard traction controller measures the wheelspin to control it by an anti-lock braking system mechanism.
Q11.) What does the service StabiliTrak mean for my Chevy Impala?
Answer: The Service StabiliTrak is a serious issue which means your system is either not responding properly or not operating at its best.
The cost for correcting it can easily be $120 +/.
Q12.) What does the service StabiliTrak mean on an equinox?
Answer: It helps by driving one in a straight line, and it does so by regularly adjusting and monitoring the steering, brakes, and your vehicle’s traction over time.
Q13.) Can a bad alignment also cause StabiliTrak problems?
Answer: Yes, for instance, if something is incorrect in the suspension or the wheel alignment tech is not properly set up from the front toe area, problems will come.
Q14.) Why can my car shake at high speeds if I brake?
Answer: We call this phenomenon a brake shudder where everyone feels a strong vibration across the steering and suspension when we apply the brakes.
The most common reasons for this anomaly are damaged rotor set and caliper and brake pads malfunction.
Q15.) What does the service StabiliTrak issue mean on Chevy Impala 2014-15?
Answer: Most often, it can show issues with its electronic ESC, and you have to face symptoms like ABS issues or a bad wheel sensor.
Q16.) How to turn off the StabiliTrak on a 2011 Chevy Impala?
Answer: Find a button on your left of the steering wheel and click on a lower button from a set of buttons and knobs.
Then its symbol will blink at the dash display, and congratulations, your traction control disables.
Q17.) What StabiliTrak means on GM’s vehicles?
Answer: It is the name for its ESC or electronic stability control system, a mandatory safety feature across all its models.
It helps to provide stability and traction, such as by applying anti-lock brakes.
Q18.) How much can the StabiliTrak service cost with labor and installation?
Answer: Replacement costs, $80 to $195, This includes LABOR costs.
PS – Labor costs vary between $25 to $50.
Q19.) Should we drive with a bad wheel speed sensor?
Answer: No, it is quite unsafe to do so because the car’s computer is not in the position to detect the speed of your travel, and it can apply brakes at any speed, causing some issues to engine power.
Final Verdict:
StabiliTrak is a GM specifically designed vehicle stability system for vehicles.
It operates by using sensors to assess whether your vehicle responds properly to your input during emergencies.
It then uses the information to apply a particular brake or reduce the engine’s power to stop the slide.
And this ensures that your Cruze point in the correct direction.
For example, if you were driving on an icy road, and your Cruze was not steering as you wanted the car to do, StabiliTrak might apply one of the brakes in the rear to guide you in the correct direction.
Fix it on time to avoid any circumstances later.
Thanks For Reading!